Published 4 November 2026 · 13 min read · Installation
An ANPR camera reads plates reliably when four things are right: the plate is large enough in the frame, the camera sits at a workable height, the horizontal and vertical angles stay shallow, and the trigger fires while the plate is inside the read window. The model, the sensor and the neural-network engine only add headroom on top of those four. Get them wrong and a good camera underperforms a cheap one that was aimed properly.
This is the installation procedure we hand to integrators deploying SZGOING ANPR units, written for a fixed camera on a pole at a lane, a gate or a gantry. It assumes the specifications that apply across our ANPR range: a 5 to 40 metre read window with the standard 5 to 50 mm motorised zoom lens, a recognition angle of up to 65 degrees left and right and 60 degrees up and down, a capture rate of 99.9 percent or better, and a recognition rate of 98 percent or better.
Start from the plate, not from the pole
The first decision is not pole height. It is where the plate will be when you want it read, and how much of the image width the plate has to share with the rest of the scene.
Plate recognition is optical character recognition, and OCR needs pixels. Across a plate, aim for at least 120 pixels of width. Below roughly 100 pixels the character edges start to merge and the confidence score drops sharply; above 200 pixels you are paying for resolution the engine cannot use. That single number decides the frame width you can cover, and the frame width decides how many lanes one camera can serve.
The arithmetic is short. A 1080p stream is 1920 pixels wide. If a plate must occupy 120 pixels, the plate has to fill 120/1920, which is 6.25 percent of the frame width. A European plate is 520 mm wide, so the widest frame that still gives 120 pixels per plate is 0.52 / 0.0625, or about 8.3 metres. A US plate is 305 mm wide, which allows about 4.9 metres.
That is why a two-lane approach of roughly 7 metres is the practical limit for one unit while three lanes of 3.5 metres each is not: at 10.5 metres of frame width a European plate lands near 95 pixels and recognition starts to fail at the edges of the lane. It also tells you what to do when the geometry is fixed and the lanes cannot be split: mount closer, or accept reading only the near lane.
Once the working distance is chosen, zoom matters less than people expect. The 5 to 50 mm motorised lens exists to let you fill the frame from whatever distance the site gives you, not to extend the read window. Zooming in from 60 metres narrows the field of view so much that the plate has to pass through a very small area, and any vehicle that drifts off line is missed entirely.
Mounting height by application
Mounting height follows from the working distance and the downward angle you want, not from whatever the existing pole happens to be. The relationship is plain geometry: height above the plate is roughly the working distance multiplied by the tangent of the downward angle.
The table below gives starting points for the applications we see most often. These are design ranges, not camera limits. Verify each one on site by watching a live frame at the speed the site actually runs and confirming the plate lands where the trigger expects it.
| Application | Mounting height | Working distance | Downward angle | Note |
|---|---|---|---|---|
| Parking lane, boom gate, checkpoint | 1.5 - 2.5 m | 4 - 8 m | 10 - 20 degrees | Slow traffic, plate often angled towards the camera. Keep the unit close to the lane edge, not above it. |
| Site gate and compound entrance | 2 - 3 m | 5 - 12 m | 10 - 20 degrees | Vehicles stop or crawl. A virtual loop is usually enough; check for tailgating. |
| Urban intersection, two lanes | 4 - 6 m | 15 - 30 m | 10 - 25 degrees | Two lanes per unit at 1080p. Above six metres the downward angle starts to flatten the plate. |
| Highway and tolling gantry | 5 - 7 m | 20 - 40 m | 10 - 20 degrees | Match the height to the gantry beam. Use radar or a physical loop where lanes are wide and speed is high. |
| Weighbridge and logistics yard | 3 - 4 m | 8 - 15 m | 10 - 20 degrees | Trucks present plates higher than cars. Set height from the truck plate plane, not the car plate plane. |
Starting ranges for common ANPR installations
Angles: the camera tolerates more than you should use
The camera tolerates a wide angle. It recognises plates at up to 65 degrees horizontally and 60 degrees vertically. That tolerance is headroom for difficult sites, not a target. In practice, stay inside 30 degrees horizontally and 20 degrees vertically, and the capture rate will sit at the top of the specification instead of drifting towards its lower edge.
Two things go wrong as the angle opens up. Horizontal offset compresses the characters along the plate, so a plate read straight on becomes a narrower shape with darker gaps between characters. Vertical offset adds perspective distortion that makes the top and bottom of each character uneven. Both effects cost recognition confidence before they cause an outright failure, which is the harder problem: the camera keeps returning plates, some of them wrong, and nobody notices until the access-control log is audited.
Aiming across the lane rather than down it also helps the trigger. A camera looking along the direction of travel sees a plate that changes size quickly and is partly hidden by the vehicle in front. A camera looking across the lane sees every plate at a similar distance and a similar size, which makes the virtual loop far more predictable.
Choosing the trigger
The trigger decides when a frame is sent for recognition, and it is the part most often left at its default. There are four options, and the choice depends on whether vehicles stop, whether lane discipline is good, and whether you can cut the road surface.
| Method | How it works | Best for | Caveat |
|---|---|---|---|
| Virtual loop | A region drawn on the image. Recognition fires when a vehicle crosses it. | Free, no civil works, adjustable from the browser. | Needs a clear view of the lane and reasonable lane discipline. |
| Physical inductive loop | A loop cut into the road surface detects the vehicle and fires the camera. | Works in rain, darkness and heavy traffic; very predictable. | Requires cutting the surface and a detector card; a repair job if the loop fails. |
| Radar | Doppler radar detects approach speed and position, then fires the camera. | Best for high-speed and multi-lane approaches; gives speed as a bonus. | More expensive, and needs careful alignment to avoid adjacent-lane triggers. |
| Continuous / manual | The camera recognises on every frame, or on a manual command. | Useful for testing and for very low traffic volume. | Wastes processing and creates duplicate records at speed. |
Trigger options compared
Lens, focus and exposure
Set the lens at the working distance with a real vehicle or a plate target in the lane, not at a wall. Focus on the plane where the plate will be, and recheck it after the zoom is locked: on a motorised lens it is easy to zoom after focusing and end up slightly soft, which costs more recognition accuracy than a small aiming error.
Exposure is the setting that separates a highway installation from a car park one. At 150 km/h a vehicle covers 41.7 metres per second. At an exposure of 1/500 s the plate moves 8.3 centimetres during the frame, which smears a 5 cm character into a grey streak. At 1/2000 s the movement is 2.1 centimetres, which a plate character survives. For highway and tolling work, keep the shutter at 1/1000 s or faster and let gain and the six built-in fill lights carry the exposure. For parking lanes at walking pace, 1/250 s is plenty and the image stays cleaner at night.
Test at night with headlights on. A plate lit by headlights sits next to a very bright source, and automatic exposure that is tuned in daylight will either blow out the plate or leave it too dark. Set the exposure manually, then confirm on a recorded frame that the characters are separated and the plate border is visible.
Power, cable and backhaul
Power and backhaul are the two items that turn a two-hour installation into a two-day one, so decide them before the pole goes up.
Wired sites. The ANPR models run on PoE or 12 V DC. PoE keeps the installation to one cable and puts the camera on the same uninterruptible supply as the switch, which is what you want at a gate or a tolling lane. Respect the cable run limit for the PoE standard in use, and put surge protection on any cable that leaves the building, because a pole in an open yard is the tallest earthed object around.
Sites with no network. The 4G LTE models remove the cable run entirely, and the version with a built-in 512 GB NVR removes the server room as well. Budget the uplink rather than the download: H.265 at 1080p runs from about 256 kbps to 8 Mbps depending on scene complexity, and plate records themselves are small. If the site also needs live viewing, size the SIM plan for continuous video, not for occasional snapshots.
Sites with no power. The solar configurations pair a 200 W panel with the camera and a 4G router. Solar sizing is a winter calculation, not a summer one: work from the shortest day at that latitude, add the router and the fill lights to the load, and allow for several days of low irradiance. Panel output also falls as the panel ages and as dust accumulates, so a system sized exactly to the load in June will brown out in December.
Integration. Confirm what the downstream platform expects before the pole is fixed. Plate records can leave the camera over ONVIF Profile S into a Hikvision, Dahua or Uniview recorder, or over TCP, HTTP or MQTT through the SDK on Windows and Linux. Getting a sample record into the platform on the bench first saves a second site visit.
On-site commissioning checklist
Work through this list on site, in order. Each step takes minutes and each one prevents a class of problem that is expensive to diagnose later.
- Record the geometry. Write down working distance, mounting height, lane width and the downward angle. Future faults are usually a geometry question, and nobody remembers these numbers a year later.
- Aim at the plate plane. Pan and tilt so the centre of the frame sits on the near edge of the read window, where plates are largest, not on the horizon.
- Zoom until the plate measures about 120 to 150 pixels wide on a recorded frame at the working distance. Use a real vehicle at the speed the site runs.
- Lock focus after zooming, then confirm sharpness at both ends of the read window.
- Set the shutter for the approach speed: 1/1000 s or faster on highways, 1/250 s in car parks. Verify on a frozen frame, not on live video.
- Draw the virtual loop, or align the physical loop or radar, so the trigger fires while the plate is comfortably inside the read window rather than at its edge.
- Run twenty passes at the expected speed and direction, and check the recognition log rather than the live view. Twenty consecutive correct reads is the minimum to sign off.
- Repeat at night with headlights on, then confirm the output format reaches the platform, and label the pole with the camera address and install date.
Twenty consecutive reads tells you the installation is not obviously wrong. It does not tell you the site will hold a 99.9 percent capture rate, because a single clean run of twenty says almost nothing about a rare failure. Proving a rate takes a stratified test with a sample sized to the claim, and the sample arithmetic, the strata that have to be tested separately and a five-minute diagnosis for a single miss are set out in how to test a license plate capture rate on site.
Five mistakes that cost the most
These five account for most of the support cases we see, and all of them are visible in the first ten minutes of a site visit.
- Mounting too high. A camera eight metres above a car park lane looks authoritative and reads badly, because the downward angle flattens the plate. Lower the pole or move the camera back.
- Aiming along the road instead of across it. Plates change size too fast, and the vehicle ahead blocks the view. Aim across the lane.
- Drawing the virtual loop where the plate is small. The loop gets placed at the far edge of the frame because it is easy to draw there. Put it where the plate is largest.
- Leaving the default shutter. The factory default is tuned for general surveillance. It will not freeze a plate at highway speed.
- No surge protection and no grounding. A pole in an open yard takes induced surges through long cable runs. The camera then fails intermittently in exactly the weather that matters.
Related pages
Installation questions we get asked
What is the correct mounting height for an ANPR camera?
For a parking lane or gate, 1.5 to 2.5 metres above the plate plane at a working distance of 4 to 8 metres. For an urban intersection, 4 to 6 metres at 15 to 30 metres. For a highway gantry, 5 to 7 metres at 20 to 40 metres. The height is a consequence of the working distance and the downward angle you want, so set the distance first and derive the height rather than the other way round.
How far can an ANPR camera read a plate?
The SZGOING ANPR range is specified for a 5 to 40 metre read window with the standard 5 to 50 mm motorised zoom lens. The usable distance at the far end depends on the plate size and the frame width, not on the lens alone: at 1080p a European plate needs about 8.3 metres of frame width to stay above 120 pixels, so a single unit covers roughly two lanes at any distance inside the window.
Can I mount an ANPR camera on an existing CCTV pole?
Usually yes, provided the pole gives you the height and the offset you need and you can reach it safely for aiming. Two constraints decide it: the pole must not put the camera at a steep downward angle to the lane, and it must carry a supply that can run the camera plus its fill lights. A pole positioned for general surveillance is often too high and too far back for plate reading.
Do I need a physical loop, or is a virtual loop enough?
A virtual loop, drawn on the image, is enough for gates, compounds, car parks and most urban intersections, and it costs nothing to install. A physical inductive loop or radar is worth the extra cost where vehicles stop and start, where lane discipline is poor, or where speed is high enough that the trigger point has to be precise. Many highway installations use radar so the trigger and the speed record come from the same device.
What shutter speed do I need at highway speed?
At least 1/1000 s, and 1/2000 s if the plate is small in the frame. A vehicle at 150 km/h covers 41.7 metres per second, so a 1/500 s exposure smears the plate by 8.3 centimetres, which is longer than a character. Use the fastest shutter the light allows and let gain and the built-in fill lights carry the exposure.
Can an ANPR camera run on solar power and 4G?
Yes. The solar configurations pair a 200 W panel, battery storage, the camera and a 4G router, and the 4G LTE model with a built-in 512 GB NVR removes the need for a server room as well. Size the panel from the shortest day at that latitude and include the router and fill lights in the load, because a system sized on summer output will drop out in winter.
Send us the site and we will specify the install
Send us the site layout and we will come back with the mounting height, the working distance, the model and the lens setting for that approach. If the pole already exists, include its height and its offset from the lane, and a photo of the approach taken from the pole.
Or email goingtech@sz-going.cn · +86 755 8395 5458